Optimizing Safety: BSC Installation and Maintenance Best Practices

By狗万官网在哪里找18 September, 2023

Biological Safety Cabinet Overview

ABiological Safety Cabinet (BSC)is a specialized type of enclosure commonly employed within laboratory settings to safeguard laboratory personnel from potential exposure to hazardous substances.This cabinet operates on a principle of controlled airflow, creating a barrier between the laboratory environment and any samples or materials that might carry biological, chemical, or other risks.

The primary purpose of aBSCis to provide a controlled and contained workspace where procedures involving potentially harmful materials can be carried out safely.The cabinet's design includes high-efficiency particulate air (HEPA or ULPA) filters that purify the incoming air and exhaust air, effectively removing any airborne contaminants.This filtration system ensures that any harmful particles generated during experiments or manipulations are trapped and prevented from escaping into the laboratory environment.

There are different classes ofBSC, each offering varying levels of protection based on their design and airflow configurations.Each BSC class is designed to meet specific containment needs and is subject to stringent testing and certification to ensure it operates effectively.The airflow patterns are carefully engineered to minimize the risk of cross-contamination and protect both the laboratory personnel and the work being conducted within the cabinet.

Choosing the right class depends on the type of materials being handled, the level of risk, and the laboratory's safety protocols.Here's a brief discussion of BSC classes:

	Photo	Purpose	Airflow	Use
Class I BSC	AC1-E	personnel and environmental protection but offer no product protection	unidirectional airflow, with air drawn from the laboratory into the cabinet and then passed through a HEPA filter before being exhausted	for working with low to moderate-risk biological agents
Class II BSC (3 Types) Class II Type A1 Class II Type A2 Class II Type B1 and B2	LA2-S G4	provide both personnel and environmental protection, along with product protection	laminar airflow, with a portion of the air recirculated within the cabinet and the rest exhausted after HEPA filtration (Type A, B1) or with 100% exhaust system (Type B2)	ideal for work involving pathogens that require containment
Class III BSC	AC3-4B	highest level of containment and protection	total containment with airtight, gas-tight construction.All operations are conducted through glove ports	designed for work with highly infectious and hazardous agents.

Biosafety cabinets can also be categorized as ducted (connected to an external exhaust system) or ductless (using internal filtration) based on how they handle airflow and contamination.Ducted cabinetsvent air outside, providing maximum containment, whileductless cabinetsfilter and recirculate air, offering versatility and cost-effectiveness for lower-risk applications.

Ducted BSC

AB2-S

Ductless BSC

AC2-E

Biosafety cabinets are commonly used inmicrobiology, immunology,pharmaceutical research, and other scientific disciplines where working withpotentially infectious agents,toxic chemicals,ordelicate samplesis a routine part of laboratory work.By maintaining a contained and controlled environment, these cabinets play a critical role in ensuring the safety of researchers, preventing the accidental release of hazardous agents, and safeguarding the integrity of scientific experiments.

Microbiology

Cell/Tissue Culture

Diagnostic Lab

狗万官网在哪里找is a leading laboratory manufacturer of biological safety cabinets, providing an extensive range of options across different classes, types, and applications.

Installation Guidelines for Biosafety Cabinets

Biosafety cabinet installation is crucial for safety and effectiveness.It ensures BSCs work properly, meet regulations, and prevent contamination.Proper installation reduces risks and extends BSC life, while also facilitating training and documentation for compliance.

Location Requirements

Location requirements for a BSC are critical to ensure its proper operation and safety.These requirements prioritize maintaining proper airflow, preventing disturbances, and optimizing the working environment for personnel.Consulting experts can help make informed decisions regarding placement for the best possible outcomes.

Never place cabinets in line with doors, openable windows, or busy paths.Also, consider how room devices like diffusers, fans, extractors, and vents might affect the BSC, and address any airflow issues before installing.
The cabinet should be placed as far away as possible from sources of airflow disturbance and positioned away from any external airflow disturbances.
Keep room air supply diffusers at least 1.5 meters (5 feet) away from the cabinet's front opening.If needed near a BSC, ensure low discharge velocity.
Position the BSC to meet operator and nearby workers' spatial needs for vision, lighting, and access.If it's on a benchtop, align the front with the bench's edge.
Avoid gaps between the cabinet's front edge and the bench to prevent turbulence and airflow disruption.
The armrest can be removed to reduce the overall depth of the cabinet if necessary.
Proper cabinet placement is vital for performance!consult facility engineers and safety experts before installation.

Position Requirements (Based on NSF/ ANSI 49: 2022)

Clearance from adjacent walls or columns (typically 6 inches or 150 mm).
Space between multiple BSCs (again, around 6 inches or 150 mm).
Adequate space, typically 6 inches or 150 mm, should be maintained behind and on both sides of the cabinet to allow for service access.
A minimum of 40 inches (1020 mm) of open space in front of the BSC for user comfort and safety.
Proper distance (usually 60 inches or 1520 mm) from opposing walls, benchtops, and areas with occasional traffic.
Approximately 20 inches (510 mm) between the BSC and benchtops along perpendicular walls.
A substantial distance (typically 100 inches or 2540 mm) between two BSCs that face each other.
Adequate space (typically 60 inches or 1520 mm) away from the rear of a doorway.
A minimum of 40 inches (1020 mm) from the adjacent swing side of a doorway.
Clearance of about 6 inches (150 mm) from the hinge side of an adjacent doorway.
For BSCs without exhaust systems, 12 inches (300 mm) clearance is required from the filter face and overhead obstructions in their final operating position.It is important for:
- Exhaust HEPA/ULPA filter testing
- Thermal anemometer use in cabinet inflow calculations

Environmental Requirements

For indoor use only.
Suitable for altitudes up to 2,000 meters (6,600 feet)!higher altitudes might require airflow sensor calibration.
Keep relative humidity between 20% and 90%.
Operate at temperatures ranging from 18°C to 30°C (65°F to 86°F).

Exhaust Requirements

The exhaust filter area is sensitive to air currents or drafts.
Maintain a 30 cm (1-foot) clearance between the cabinet's highest point and the ceiling.
If the clearance is less than 30 cm, consider recalibrating the airflow alarm system.
For effective exhaust filter leak scanning, aim for a minimum 50 cm (1-foot 8-inch) clearance.

Best Practices for BSC Operation

BSC usage tips and reminders are essential for maintaining a safe, compliant, and efficient laboratory environment.They safeguard personnel, samples, equipment, and data while ensuring the quality and reliability of research and diagnostic processes.Adhering to these practices is a fundamental responsibility in any laboratory setting.

Biosafety Cabinet Maintenance

a.Scheduled Maintenance

Regular maintenance is necessary for the Biological Safety Cabinet's trouble-free performance.Stay on track and take note of the checklist below.

Table 1.Scheduled Maintenance Checklist

No.	Description of Task to Perform	Maintenance to be carried out every
No.	Description of Task to Perform	Day	Week	Month	Quarter	1 Year	2 Years
1	Surface decontaminate the work zone	✔
2	BSC power-up alarm verification	✔
3	Perform thorough surface decontamination on the drain pan		✔
4	Check the paper catch for retained materials		✔
5	Clean UV lamp (where present) of any dust and dirt			✔
6	Clean the exterior surfaces of the BSC			✔
7	Clean the sash window	✔
8	Check all service fixtures (where present) for proper operation			✔
9	Inspect the BSC for any physical abnormalities or malfunction				✔
10	Clean stubborn stains on stainless steel surfaces with MEK
11	Recertification					✔
12	Check the cabinet's functionality					✔
13	Change UV Lamp (where present)					✔
14	Change the fluorescent lamps						✔
15	Change pre-filter (if any/present)					✔

b.Certification

Certification of cabinets, particularly Biosafety Cabinets, is a fundamental practice in laboratory safety.It involves conducting a thorough assessment of the cabinet's performance to reduce the risk of unexpected malfunctions that could compromise user safety and the integrity of experiments or processes.

狗万官网在哪里找Esco Lifesciences conducts the following BSC performance testing to ensure they meet global standards for performance, safety, and compliance, reflecting commitment to quality and safety in labs and research.

Inflow velocity testmeasures the inlet volumetric flow rate on the front aperture at nominal operating speed.
Downflow velocitytestmeasures the movement of air out of the cabinet and determines the performance of the blower.
Particle count testdetermines air quality by counting and sizing the number of particles in the air and classifying the cleanliness level in a controlled environment.
Filter integrity testverifies the continued efficiency of the filter by introducing particulates and measuring the output.
Light intensity testdetermines light intensity from fluorescent/LED lamp in front to back centerline work surface level of the cabinet.
Noise level* testdetermines noise level of the cabinet during normal operation in front of the work surface area lower edge and above the recessed work surface area.
UV intensity* testdetermines the light intensity from UV lamp in front to back centerline work surface level of the cabinet.
Smoke pattern testdetermines the inward airflow at the work access opening, the downward air movement within the working area, the absence of ambient air on the work surface, and that airflow within the cabinet does not escape from the sides and top of the sash.

*Note: This test is optional for field testing.

狗万官网在哪里找Esco Lifesciences BSC Field Certifiers conducting Biosafety Cabinet performance testing.

c.Cleaning Procedure

Clean the work surface and walls with disinfectant and soapy water.
Clean the sash window with disinfectant and glass cleaner.
Use a damp cloth to clean the BSC's exterior, especially the front and top, to remove dust.
Finish by washing with sterile water to remove any cleaning residue.
For tough stains on stainless steel, use MEK and immediately wash with sterile water and liquid detergent.Use a polyurethane cloth or sponge.
Ensure chemical compatibility.
Wear appropriate personal protective equipment (PPE) during cleaning.

Overall, biological safety cabinet installation, safety tips, and maintenance are essential for lab safety, experiment reliability, regulatory compliance, cost-efficiency, and emergency preparedness.Be equipped with knowledge whenever you use Biosafety Cabinets and heed the given installation and maintenance guide to let your BSCthrive.

狗万官网在哪里找Discover the latest Esco Lifesciences Biosafety Cabinet:Labculture® G4 Class II Type A2 BSC with Centurion Touchscreen Controller

Ready to learn more about Biosafety Cabinets?Reach out to us today!